FAQ

News

Support

Partners Area

Power button on front of OP-MT8121X is resetting touch screen panel when decorative frame is on. Is it possible to disable this button?

The power button on the front panel of OP-MT8104XH, OP-MT8121X or OP-MT8150X can be disabled by setting DIP switch 4 "OFF". After the function is disabled, the power button will wo ... More >

How do I install OP-MT6070IH and OP-MT8070IH in wall?

OP-MT6070IH and OP-MT8070IH have to be fasten to fixing frame from top and bottom side. Fastening is not possible from left and right side. Panel fixing pins must be inserted and fastened in posit ... More >

Is the cable for connecting OP-MT6050I with CyBro the same as for connecting OP-MT6056I to CyBro?

Serial connector pin assignment is different for different types of operator panels. Cables for RS-232 connection should be: Order code for these cables: - CAD-OPTW-P2 for panel OP-MT6050I ... More >

How could I connect multisensor LRI 8134 to IEX module LC-DC?

For connection 6 wire cable with RJ-12 modular plugs on both sides is needed. Type of connection is straight through. Connection is the same for modules LC-S, LC-D and LC-DC. ... More >

Can I use mask system on OP-5 panel?

Mask system works with OP-5 like with other operator panels on IEX bus. The only differences that keys are positioned different. Use key_p for entering mask system, key_up and key_dn for changin ... More >

How to set CyBro analog inputs for voltage or current measurement?

Unplug terminals and remove terminal covers. Inside the device are 4 DIP switches. Each analog input can be set independently to voltage or current measurement: DIP switch ON: 0(4)..20 mA. ... More >

Is it possible to measure with Pt100 and Pt1000 probes connected to one AiR-12 module?

Temperature measuring probes Pt100 and Pt1000 can be used at the same time on AiR-12. System will automatically detect which type is connected to particular input. Precaution is needed when dealing ... More >

Could I perform 2 and 3 wire temperature measurement with Pt100 probes connected to one AiR-12 module?

2 and 3 wire measurement on one AiR-12 module at the same time is not possible, because selecting measuring input mode can be set for whole module. ... More >

What is mounting height for touch screen panels in building automation applications?

There is no rule for this issue. When projecting building automation application you should consult architect and investor to get their opinion on mounting height. In general Cybrotech recommend mou ... More >

Are CyBro-2 and Integra-BM systems compatible?

Integra-BM and CyBro-2 systems are fully (electric connections and software protocols) compatible. But care should be taken because Integra-BM applies to home standards and CyBro-2 applies to industri ... More >

Can I use CyBro-2 PLC for building automation applications?

From the technical view CyBro-2 and Integra-BM systems are fully compatible and CyBro-2 PLC can be used in building automation systems, but special care should be taken because CyBro-2 devices applies ... More >

How long does the warranty for CyBro-2 and Integra-BM products last?

Cybrotech products are warranted for 36 months from delivery. More about the warranty time and conditions: . Cybrotech warranty regulations ... More >

What are differences between serial ports COM1 and COM2?

COM2 is like COM1 a multi-purpose serial RS232 port. In most cases ports COM1 and COM2 are equal, but there are three differences: - Kernel can be only send by using port COM1, - COM2 port ... More >

Can I use serial ports COM1 and COM2 at the same time?

Serial ports COM1 and COM2 can be used at the same time. ... More >

How to lock the program in CyBro-2 plc, to prevent uploading from CyBro-2?

There is no classic way to lock your program inside CyBro-2 plc with password. But there is a way to prevent uploading program from plc. You can send program to plc without source code. To do so p ... More >

What is NAD?

NAD is network address number of module. When connected in network type and network address are used for module identification.  It is also a serial number written down on a label that is placed ... More >

Is in CyPro an easy way for setting variable default value?

Instead of writing program code there is an easy option to set up default value to variable. Open Global Allocation Editor, select variable and open properties window for selected variable. In defaul ... More >

What is mask system?

Visual tool for programming operator panel, used to enter parameters. Capable of entering integer values, decimal values and values represented by strings. Parameters may be hierarchically organized. ... More >

Why is IPU designed with non-removable terminals?

IPU is designed to fit in prepared place inside frequent converter Hitachi L300P or SJ300. Because of dimensional limitations in that place, only non removable, 45º input angle connectors can be ... More >

What are the differences between Bio-8R4 modules?

There are three different types of Bio-8R4 module available. Two modules are designed to be used for a specific purpose while one is meant to be general purpos. Bio-8R4-N Bio-8R4-N is a high powe ... More >

What is the difference between LC-S and LC-D?

LC-S and LC-D are both light controllers with the same input points. The difference is in type of regulating ballasts that can be controlled by LC-S or LC-D: LC-S is designed for analog (0..10V) elec ... More >